• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Door Lock Replacement - What You Need to Know

When the locks on your patio door locks replacement begin to begin to show signs of wear and tear, it's usually recommended to replace them. These signs include things like having difficulty turning the lock, or a key that doesn't fit.

It is good to know that installing new composite door replacement lock lock hardware is actually very easy. All you need to do is follow these steps.

Deadbolt

The deadbolt is the primary defense of your door against forced entry. It's stronger and more secure than the latch that opens the lock, so you'll need to ensure the deadbolt you purchase is sturdy enough to meet your requirements. If possible, opt for a deadbolt made of case-hardened steel that has no exposed screwheads on the exterior to stop unauthorized drilling. The inside of the deadbolt should also be inserted into the door frame to improve security.

During the installation process, check that your new deadbolt's bolt extends smoothly into the strike plate after you lock and close the door. If not, mortise the bolt into the strike plate with the help of a wood chisel before you install the deadbolt. Make sure that the doorknob's latch is in contact with the hole for the deadbolt when you lock and close the door, too.

Make sure whether the new deadbolt is compatible with the old one before installing it. The majority of door locks come with an example of how far the bolt should be above the doorknob. However, it's always recommended to speak with an expert in the field in case you aren't sure of the backset measurement you need for your doors. They will be able to direct you to models that will work with your patio doors locks replacement and existing deadbolt opening.

Install the bolt assembly into the hole in the door after making sure it is the correct length. Screw the latch faceplate in place if your new deadbolt comes with one. It's an excellent idea for you to screw the latch faceplate using the recommended screws to the frame.

Some lock sets have a "dummy" or decorative bolt that allows you to put in the keyed deadbolt and still have a functioning latch. If you're using this type of lock, a dummy bolt should be installed with the same screws that are used for your latch faceplate, and it's important that the two fit together correctly to ensure maximum security.

Some deadbolts can only be opened via a thumb-turn from inside and others have two cylinders that allow both keyed and non-keyed access. No matter which type you select it's best to buy a commercial grade lock for the highest level of security. They're typically tested to last for 250,000 open and close cycles before being sold to homeowners.

Latch

The latch is the part of the lock that retracts the bolt to open and close the door. It is usually secured with screws on the sides, but can also be attached to the strike plate of the door jamb. It's important that you replace a door latch with the right one for your current hardware. You can either hold the latch against the hardware you have already installed or look up the label on a new. Dunn Lumber carries a variety of brands, but it's generally best to use the identical brand as your current hardware to ensure you get an appropriate latch that fits properly.

Some doors feature an ahasp instead of a latch. A hasp is made up of a strap with a slot punched in it that can be placed over the staple. The staple is then fixed to the door frame or door with nails. When the door is shut, the strap will pull the staple down and secures it into the frame. A hasp is typically used in commercial buildings because it's cheaper than a deadbolt.

Locks are susceptible to wear and tear over time, just like any other mechanism that has moving parts. Sometimes the internal mechanism will start to "stick" and become difficult to turn, making it necessary to replace the entire lockset. Sometimes, the doorknob on the outside will be damaged and it is important to replace that as well.

If your lock is stuck, you can apply some graphite to the keyhole. You can either spray it on the key or rub it onto the inside of the lock, then use the lock a few times to incorporate the graphite into the mechanism. You can also use a screwdriver to remove the knob and reveal the inside components and allow you to observe what's going on inside.

After removing the knobs then tighten the three or two setscrews at the edges of the cylinder by turning them clockwise. You should also remove the faceplate and replace lock on patio door it. Surface-mounted rimlocks also have an additional set cylinder setscrews on the back of the case that must be removed as well as the faceplate.

Strike Plate

The strike plate, connected to the door frame above the holes that accommodate the master key bolt or deadbolt system bolt, reinforces and enhances the locking mechanism. It helps keep intruders out by ensuring that the lock's latch is secured in the strike plate when the bolt or latch is engaged. A strikeplate that is of high-quality can improve the longevity of locks as well as increase security.

Standard strike plates are flat metal plates with holes, or several holes cut into them. It is attached to the door frame typically using screws, which gives the latch something to sink into as it closes. The strike plate has to be aligned precisely with the lockset to provide the greatest protection against burglaries.

If the strike plate on a door is damaged, you must replace it as soon as you can. This will ensure that your door can close and latch correctly. To replace a strikeplate you must first ensure that it is properly aligned with the bolt hole in the doorjamb. An easy way to accomplish this is to place a piece of tape across the bolt hole. Then, test the latch by opening and closing the door. If the latch doesn't catch, you must remove the tape and then chisel the area to ensure that the strike plate will be flush with the doorjamb.

Once the area is chiseled out, it is important to use a larger screw to anchor the strike plate. They should be at least 3 inches in length to ensure that they are securely anchored into the stud behind the trim board. If you do not install the longer screws or the wood inside the doorjamb could break in the event of a kick-in attack by a burglar and make the door vulnerable.

A professional locksmith is able to quickly replace a strike plate that's been damaged or worn out. They can also install new strike plates on doors that never been fitted with them before. They can also modify existing strikeplates to enhance the security of a building as well as its aesthetics. This could help property owners draw in tenants looking for a safe and secure living environment and peace of mind.

Keys

The key cylinder is a part of your lock that accepts a specific key to move pins into place so the inner handle can be turned. The cylinder is also the most important component of your door lock as it fulfills the purpose that locks were designed to do - protecting you, your family members and your belongings. Rekeying locks is a cost-effective option than replacing them.

The procedure of replacing upvc door locks the lock is more complicated than simply swapping out the existing handle-lock combo or deadbolt. The old cylinder, hardware and handle (if you have the knob and lock combo) must be removed from the door before the new lock is installed. While there are a number of DIY-friendly kits that can be used to replace a lock yourself but it is highly recommended that you contact a skilled locksmith to ensure the job is done properly.

It is essential to have the right key before you install your new lock and the cylinder. A key that is a duplicate will not work properly and could cause the lock to fail completely, rendering it impossible to open. A trained professional can help you avoid this by making sure that you have a working, genuine key for your home.

The next step is to remove the faceplate and then the latch plate. To take off the screws that hold them in place, you'll require an screwdriver. You may want to leave them in place if the plates you are replacing are identical to the originals. This will cut down on time. If you need to replace them, be careful not to tighten too much the screws since this can cause them to lose their grip on the door.

After you have removed the plates, you'll be required to measure the door to determine the proper size of the lock. While most modern locksets can fit on a standard thickness of door, it's best to know the dimensions of your door in advance to avoid frustration when you visit the hardware store. Be aware that doorknob locksets tend to be different sizes than deadbolt locksets, and commercial models may have an enlarged bolt or latch.