• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix a Loose Door Hinge

Fixing a door hinge that is loose can be a doable job for most homeowners. If, however, the holes for screws are smashed and aren't able to hold screws, you may need to put in dowels and wood glue before you can reinstall the hinge.

Brush away any surface rust. This will help the dowels stay in place and give them a solid base to grip into.

Remove the Hinges

Many hinges for doors can be removed, making it easier to move a door from one side of the frame to the other or take the entire door off in the event of need. It is simple for anyone with a little patience, though you do have to know how to do it properly.

If the hinges are painted, you will need to remove the paint before attempting to remove the pins. You may scratch your door if you don't take off the paint. Put the hinges in the stainless steel pot and fill it with water to the point that the hinges are completely submerged. The hinges should remain in the pan for around 30 minutes. The heat from the water should soften the paint and make it easier to get rid of the pins.

After the pins have been loosen, you can remove the hinges from the door and frame. You can make use of a screwdriver to get the job done, but it is recommended to use a magnetic screwdriver for this project. This type of screwdriver has been specially designed to pick up screws made of metal and will aid you in getting the job accomplished much faster.

Before you attempt to remove the hinges it is recommended to spray them with grease. A simple lubricant can make the process go by more quickly and aid in the removal of the pins and screws. You can purchase this kind of lubricant at a variety of hardware and home improvement stores.

You should also keep in mind that the number of door hinges you will need will vary based on the kind of door and the configurations. Heavier and solid-cored doors will require more hinges while hollow-cored and lighter doors might only require two or three hinges.

Understanding the different kinds of window hinges repair will help you determine which one is best for your particular situation. Exterior hinges are designed to hold the weight of a door, but interior hinges need to be able to handle heavier loads.

Reattaching the Hinges

Sometimes, the hinges on doors loosen over time and start to hang in a crooked manner or slide. This could be a problem however, it's usually simple to repair. A simple retightening will usually solve the problem. However, if the screw holes have been stripped out, this can be more difficult to accomplish. A wood dowel can be used to tighten these holes again.

Start by drilling out the hole you had previously made using a drill bit that is similar to the size of the new screw (typically 3/8"). Fill in the hole using wood glue and a wooden stick. The dowel should be cut to a length the same as the screw to ensure a secure fit. Then, reinstall the screw and tighten it until the desired level of tightness. If the door continues to have an tendency to get stuck, then add another dowel to the gap and repeat the procedure. Make sure to close the door slowly to verify the clearances at the perimeter after each adjustment.

Another option is to make use of the wood plug instead of dowel. This will work as well, but may take a bit longer to install. You can use the wood piece that has been whittled down to the proper size. If you don't have a tool for woodworking, you can also use toothpicks or wooden matches.

Make use of a countersink in order to make the hole smaller for the head of the screw after you have put it back in place. This will prevent the screw from rubbing against the edges of the doors when they are closed and opened. This will make it easier to tighten the screws before replacing hinges.

Once you have reinstalled the hinge, be sure to grease it with a dry lubricant in order to help keep it from getting stuck in the future. You can use products such as PB Blaster and Liquid Wrench. Apply a thin coat and allow it to take approximately 15 minutes to get into the barrel of the hinge.

Refinishing the Hinges

If you're not ready to replace your hinges, you can try a few fixes. The first step is to check that the screws securing the hinge plate to the door frame are tight. If they're loose, tighten them with a power drill or screwdriver. Be cautious not to tighten the screws so tight that they begin to cause gaps at the trim joints, or even worse cause threads to be stripped.

If the issue is that the hinge plates are splitting they can be reattached to the plates by putting wood glue on the back of them and then inserting toothpicks or wooden dowels into the holes. The dowels or toothpicks provide a solid base for the screws and help to prevent the plates from shifting when you drive them into the holes. Allow the glue time to dry before reattaching your hinge.

The screws could also be smashed or gone. It is possible to fix door hinge this issue by replacing the screws with larger ones. Use a drill bit that is exactly the same size as the screw hole to avoid drilling into the upvc window hinge or jamb.

Once you've reattached the hinge shut the door and examine the gap between the double glazed door hinges and the frame. It should be around the thickness of one nickel all around, or less if there's a gap that was caused by a door that was not properly hung. If the hinges were put in place correctly, this should not be an issue.

If the hinges seem loose, you could add a thicker hinge between the hinge plate's surface and the mounting surface. This will give the hinges more space. You can also take off the hinge pin and then pound it down with a heavy hammer in order to tighten it or use the hinge of a different type. You can also lubricate your hinges with mineral oil or jojoba in order to reduce friction and keep them in position. Lubricating your hinges regularly can help keep them from becoming stiff or squeaky and will also extend their life.

Cleaning the Hinges

The friction generated by a hinge's constant movement attracts dust particles. Without periodic cleaning and lubrication, these particles become stuck in the moving parts of a hinge for doors and build up over time. The hinge will become stiff and creaky and its appearance could rapidly diminish. Regular cleaning, lubrication and inspections will ensure the functionality and quality of hinges that are attached to doors.

Examine the hinges for corrosion. If the rust has corroded to the point of destroying surface of the barrel or screw holes, you will have to replace the hinges. If you're able to save the hinges, remove any loose rust with a wire brush and steel wool. Apply a commercial rust-removing solution or homemade solutions like lemon juice on the hinge. Let the solution that removes rust be on the hinges for several minutes to penetrate and dissolve the remaining rust.

If you don't wish to spend the money and time replacing your hinges, simply retightening the screws will make the hinges functional again. If you have stripped the screws' holes however, it might be necessary to attach a wooden dowel or shim to the hinge. Wooden dowels are round pieces of wood in the form of rods, which are available in different sizes and lengths. They are available at home improvement stores as well as woodworking supply and craft shops, or on the internet.

You can also make an shim using metal or plastic depending on the type hinge you have. To make a dowel, cut a wooden dowel to the desired length. You can dip the dowel into the adhesive of a carpenter and then insert it into the hole. The glue will secure the dowel in place.

Before you start cleaning the hinges, put down a paper or cloth towel to shield flooring and other surfaces from drips and spills that could happen. After the area is secured, proceed to clean the hinges with a soft sponge or cloth coated with a mild cleaner or vinegar to remove the build-up of dirt, grime and tarnish. You can make use of a toothbrush or a small brush to reach hard-to-reach spots in tight spaces and crevices.